P0153 O2 Sensor Circuit Slow Response (Bank 2 / Sensor 1) - Automotive Repair Guides & Equipment

COMPONENT LOCATION

GENERAL DESCRIPTION

In order to control emissions of the CO, HC and NOx components of the exhaust gas, heated oxygen sensor (HO2S), mounted on the front side and rear side of catalytic converter, detects the oxygen content in the exhaust gas. The front HO2S signal is used to control air/fuel ratio (closed loop fuel control) and the rear HO2S signal is used to monitor front HO2S and catalyst for proper operation. The HO2S requires a minimum temperature to operate properly and provide a closed loop fuel control system. The HO2S contains the heater element to reduce its warming-up time and ensure its performance during all driving conditions. The oxygen sensor generates a voltage that indicates the difference between the oxygen content of the exhaust stream and the oxygen content of ambient air. When the exhaust stream is “rich,” there is more oxygen in the ambient air than in the exhaust stream, so the voltage will be higher.

DTC DESCRIPTION

Checking output signals from HO2S under detecting condition, if ECM judges it’s signals too slow, ECM sets P0153.

DTC DETECTING CONDITION

Item

Detecting Condition

Possible Cause

DTC Strategy

Monitor HO2S’s response rate

1.	Poor connection

2.	Faulty HO2S

3.	Faulty ECM

Enable Conditions

Engine warm-up sufficiently

Engine run time > 60sec

Drive at a steady speed between 45-55 mph(72-88 km/h)

Engine Coolant > 70°C( 158 °F)

No disabling faults

Threshold value

The calculated response rate is too slow (out of threshold in ECM)

Diagnosis Time

Continuous

MIL On Condition

3 Driving Cycles

SPECIFICATION

A/F Ratio (λ)	Output Voltage (V)
RICH	Min. 0.8
LEAN	Max. 0.1

DIAGNOSTIC CIRCUIT DIAGRAM

SIGNAL WAVEFORM & DATA

Fig.1) Normal graph of upstream HO2S and downstream HO2S at idle.

Fig.2) Normal waveforms of upstream HO2S(the upper) and downstream HO2S(the lower) (chassis ground used)

Fig.3) Normal waveforms of upstream HO2S(the upper) and downstream HO2S(the lower) (sensor ground used)

After warming-up, if accelerator pedal is released suddenly around 4000rpm, the HO2S signal reading will be lower than 200mV resulting from Fuel cut-off for the moment. Conversely, if suddenly accelerator pedal is depressed, HO2S signal reading will be around 0.6V ~1.0V. At idle, Normally HO2S signal will switch from lean to rich with 3 Hz. And as racing, Its frequency rises.

MONITOR GDS DATA

1.	Connect GDS to Data Link Connector(DLC).

IG “ON”.

3.	Select “DTC” button, and then Press “DTC Status” to check DTC’s information from the DTCs menu.

4.	Read “DTC Status” parameter.

Is parameter displayed “Present fault”?

	▶ Go to “Component Inspection” procedure.
	▶ Clear DTC and check if this DTC is set after test-driving under enable conditions. If DTC isn’t displayed after the test, it was intermittent fault.

COMPONENT INSPECTION

1.	Replace the HO2S.

2.	Clear DTC with GDS.

3.	Start the engine and warm it up until the radiator fan comes on( more than at least 10 minutes).

4.	Drive at a steady speed between 45-55 mph(72-88 km/h) for 120 sec.

5.	Stop and then maintain idle state.

6.	Check if O2 sensor monitoring readiness is complete.

Does the scan tool show DTC P0153?

▶ Substitute with a known – good ECM and check for proper operation. If the problem is corrected, replace ECM and go to “Verification of Vehicle Repair” procedure.

There is a memory reset function on GDS that can erase optional parts automaticallydetected and memorized by ECM. Before or after testing ECM on the vehicle, use this function to reuse the ECM on the others

▶ Troubleshooting is finished.

New Videos on our YouTube Channel Every Week, Subscribe Now!

Related Posts