P0262 Cylinder 1 Injector Circuit High

COMPONENT LOCATION

img

GENERAL DESCRIPTION
Based on information from various sensors, the ECM controls the amount of fuel sent to the cylinder via the fuel injection system. The fuel injector is a solenoid-operated valve that meters the fuel. The ECM controls by length of time the fuel injector is held open. The ECM grounds the injector control circuit to open the injector. When the ECM energizes the injector by grounding the control circuit, the circuit voltage should be pulled low (theoretically 0V) and the fuel is injected. When the ECM de-energizes the injector by opening the control circuit, the fuel injector is closed and circuit voltage should momentarily peak before settling back to system voltage.
DTC DESCRIPTION
Checking output signals from injectors. Under detecting condition, if an output signal is high, ECM sets P0262.
DTC DETECTING CONDITION
 
ItemDetecting ConditionPossible Cause
DTC Strategy
Signal High
1.
Poor connection
2.
Short to battery in harness
3.
Injector
4.
ECM
Enable Conditions
Engine running state
11V ≤ Battery voltage ≤ 16V
Above conditions are met > 0.5sec.
Threshold value
Short to battery
Diagnosis Time
Continuous (more than 5 sec. failure for every 10 sec.test)
MIL On Condition
3 Driving Cycles

 

SPECIFICATION
 
ItemCoil resistance(Ω)
Injector13.8 ~ 15.2 [20°C(68°F)]

 

DIAGNOSTIC CIRCUIT DIAGRAM

img

SIGNAL WAVEFORM & DATA

img

Fig.1) Normal waveforms of Injector under idle condition.
 
When the ECM energizes the injector by grounding control circuit, the circuit voltage should be low (theoretically 0V) and the fuel is injected. When the ECM de-energizes the injector by opening control circuit, the fuel injector is closed and circuit voltage should be peak at a moment.

 

MONITOR GDS DATA
1.
Connect GDS to Data Link Connector(DLC).
2.
IG “ON”.
3.
Select “DTC” button, and then Press “DTC Status” to check DTC’s information from the DTCs menu.
4.
Read “DTC Status” parameter.

img

5.
Is parameter displayed “Present fault”?
 

img

â–¶ Go to “Terminal and Connector inspection” procedure.

img

▶ Fault is intermittent caused by poor contact in the sensor’s and/or ECM’s connector or was repaired and ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, ending, corrosion, contamination, deterioration, or damage. Repair or replace as necessary
TERMINAL AND CONNECTOR INSPECTION
1.
Many malfunctions in the electrical system are caused by poor harness and terminals. Faults can also be caused by interference from other electrical systems, and mechanical or chemical damage.
2.
Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage.
3.
Has a problem been found?
 

img

â–¶ Repair as necessary and go to “Verification of Vehicle Repair” procedure .

img

â–¶ Go to ” Control Circuit Inspection ” procedure.

 

CONTROL CIRCUIT INSPECTION
â–  Check voltage
1.
IG “OFF” and disconnect injector connector.
2.
IG “ON”.
3.
Measure voltage between injector control terminal of injector harness connector and chassis ground.
 Approx. 3.6V

img

4.
Is the measured voltage within specification ?
 

img

â–¶ Go to “Component Inspection” procedure.

img

â–¶ Go to “Check short to battery in harness” as follows.

 

â–  Check short to battery in harness
1.
IG “OFF” and disconnect injector connector and ECM connector.
2.
Measure resistance between power and control terminals of injector harness connector.
 Infinite

img

3.
Is the measured resistance within specification ?
 

img

â–¶ Go to “Component Inspection” procedure.

img

â–¶ Repair short to battery in harness
COMPONENT INSPECTION
â–  Check injector
1.
IG “OFF” and disconnect injector connector.
2.
Measure resistance between power and control terminals of injector connector.(Component side)
 13.8 ~ 15.2Ω [20°C(68°F)]

img

3.
Is the measured resistance within specification ?
 

img

â–¶ Substitute with a known – good ECM and check for proper operation. If the problem is corrected, replace ECM and go to “Verification of Vehicle Repair” procedure.
   
 
There is a memory reset function on GDS that can erase optional parts automaticallydetected and memorized by ECM. Before or after testing ECM on the vehicle, use this function to reuse the ECM on the others

img

â–¶ Substitute with a known – good Fuel Pump Relay and check for proper operation. If the problem is corrected, replace Fuel Pump Relay

New Videos on our YouTube Channel Every Week, Subscribe Now!

Shopping Cart
Scroll to Top